Ph: (07) 3881 0384 Print this page

Crystal Paint

 

Why Crystal Paints?

 

Crystal Paints manufacture their own paints in Australia to meet local conditions and the needs of our customers.

This means you deal directly with the people who actually make the paint. We know what goes into it and how it will perform.

We use premium raw materials sourced in Australia and are completely Australian owned.

We have strict quality control in our manufacturing processes.

Every batch is supervised by a trained technician from start to finish. Each technician handles only one batch at a time to ensure total dedication to every batch.

Our operators have a minimum of 15 years paint manufacturing experience.

We make new colours on a regular basis. We will also make special colours to meet your needs in large or small quantities.

We can make paints to meet different applications or conditions.

 

AUTOMOTIVE PAINT

          
This is a polyurethane based enamel that is very easy to use for basic automotive,
truck, motorcycle, and machinery jobs.
 Can be brushed, rolled or sprayed.
 Re coat time is 2 – 4 hours depending on weather conditions.
 Thinning and clean up – use mineral turps only.

PREPARATION
 Can be painted onto most solid pre painted surfaces. Remove all oxidation, oils
etc. then key sand off and do a small test patch first on the prepared surface to
compare compatibility.
 Bare steel should be undercoated with crystal red or grey oxide zinc chromate
primer.
 Motorcycle plastic fairings can be sanded lightly and applied straight on.
 Automotive plastics and fiberglass can be applied straight on after a fine sand.
 Colours available white, blue, black, yellow, golden yellow, red and many lighter
colours.
 Do not mix with any other paints, solvents or additives as this could effect the
performance of the paint.
 Coverage is 10-12 square metres per litre.

WHAT ELSE DO I NEED TO KNOW?
1. If you're going to spray, you will need to thin the paint out about 5-10%
mineral turps or more depending on your spray unit.
2. Do not paint if the temperature is less then 12 degrees C.

AVAILABLE IN 1 AND 4 LITRE CANS

 
 

 

MARINE ENAMEL

 QUICK DRYING - PAINT IN THE MORNING GO BOATING IN AFTERNOON

CAN BE BRUSHED ROLLED OR SPRAYED,

TURPS BASED   NO SPECIAL THINNERS NEEDED

INTERIOR AND EXTERIOR SURFACES  -  GLOSS FINISH    AND  QUICK  DRYING

CAN BE PAINTED ONTO MOST SOLID SURFACES, REMOVE ALL LOOSE PARTICLES, DUST AND OILS AND SAND OFF

 TIMBER – BARE SHOULD BE PRIMED

 FIBERGLASS – SHOULD BE SANDED BACK TO A SOLID SURFACE NO PRIMER REQUIRED

 STEEL – BARE SHOULD BE PRIMED WITH RED OR RED OXIDE PRIMER

ALUMINUM – CAN BE APPLIED AFTER SANDING

 AVAILABLE IN  1 AND  4

 COVERAGE IS APPROXIMATELY 10-12 SQUARE METRES PER LITRE

 CAN BE EASILY SANDED

 RECOAT TIME 2 – 4 HOURS DEPENDING ON WEATHER CONDITIONS

 IF YOU ARE NOT SURE ON THE SURFACE TRY A SMALL TEST PATCH FIRST  

AVAILABLE IN  WHITE, BLACK, BLUE, DEEP BLUE, ISLAND BLUE , RED, REEF BLUE,

 SAFETY YELLOW , WHITE  AND MANY PASTEL COLOURS

 

COLOURS LEFT TO RIGHT

BLUE, LIGHT GREY,  GREEN,  BLACK, YELLOW, RED, SAFETY YELLOW,

 
 

 

INDUSTRIAL COATINGS

 

 GREY & RED OXIDE ZINC CHROMATE PRIMER

 SPECIALLY FORMULATED WITH ANTI CORROSIVE PROPERTIES FOR PREVENTING RUST ON BARE STEEL.

 STEEL MUST BE CLEANED, FREE FROM OILS, AND ALL SURFACE RUST REMOVED BEFORE APPLICATION.

 APPLICATION BY BRUSH, ROLLER, OR SPRAY.

 IF SPRAYING, THINNING WITH TURPS MAY BE NECESSARY.

 WASHES UP IN MINERAL TURPS

 DRYING TIME IS 2-6 HOURS DEPENDING ON WEATHER CONDITIONS.

COVERAGE IS 6-12 SQUARE METRES PER LITRE.

 MINERAL SOLVENT BASED TOP COATS ARE RECOMMENDED.

 DOES NOT CONTAIN ANY LEAD OR MERCURY BASED PRODUCTS.

 AVAILABLE IN 500ML 1 AND 4 LITRE CANS

Home       Contact           [email protected]                               Terms & Conditions

 

 

Updated Thu 30 Jun 2016 3:31pm

Previous page: N U K
Next page: Oil Filters